WD-40 Specialist Fast Drying Contact Cleaner 400ml Smart Straw spray

WD-40 Specialist® 400ml Fast Drying Contact Cleaner Smart Straw

Our Fast Drying Contact Cleaner spray is a non-conductive spray that is suitable for use on all sensitive electrical components. It provides excellent cleaning with minimal fuss, and removes dirt, dust, condensation and flux residue with ease. Our fast-drying electrical contact cleaner spray is ideal for use on circuit boards, switches, even spark plugs and tape heads. It will remove all the contaminants that cause current leakage and component failure. You can safely use Fast Drying Contact Cleaner on plastics, rubber and metal for superior cleaning.

Characteristics

• Cleans oil, dirt, dust, flux residue and condensation from electrical components
• Dries quickly, leaving no residue
• Is safe to use on sensitive electrical equipment
• Creeps into hard to reach areas on circuit boards and contact points
• Smart straw and 360° valve allows for precision application in tight spaces

Field of application

• Clean circuit boards
• Remove dust from electrical components
• Clean printers and copiers
• Clean switches and controls
• Remove condensation from spark plugs and electrical assemblies
• Clear tape heads

Advantages of WD-40 Smart Straw

With the Smart Straw applicator, you’ve got two ways to spray; use the flip up straw for hard to reach areas, such as inside chains, locks or rollers, then flip it down to use the wide angle spray eye for area coverage on surfaces. Whichever way you need to spray, you can rely on the clever 360° valve to work efficiently at every angle, even upside down.

Technical specifications

• Appearance: Translucent, non-viscous liquid
• Odour: Hydrocarbon
• SG: 0.70 – 0.73
• Discharge rate: 0.6 – 1.2 g/s
• Solubility: partially soluble
• NSF category: K2
• Flammability: Classed as extremely flammable under current legislation
• Compatibility: metal, plastic, rubber
• Dielectric Strength ASTM D877: 33.8 kV
• ASTM D1133 Kb value: > 62.3

Hazard Warnings (CLP)

Signal word: Danger

Hazard Statements (H-phrases)

• H319: Causes serious eye irritation.
• H315: Causes skin irritation.
• H336: May cause drowsiness or dizziness.
• H411: Toxic to aquatic life with long-lasting effects.
• H222: Extremely flammable aerosol.
• H229: Pressurised container: May burst if heated.

Safety Statements (P-phrases)

Prevention:

• P101: If medical advice is needed, have product container or label at hand.
• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P211: Do not spray on an open flame or other ignition source.
• P251: Do not pierce or burn, even after use.
• P261: Avoid breathing vapours/spray.
• P273: Avoid release to the environment.
• P280: Wear protective gloves and eye / face protection.

Response:

• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: Call a POISON CENTER or doctor if you feel unwell.

Storage:

• P405: Store locked up.
• P410+P412: Protect from sunlight. Do not expose to temperatures exceeding 50 °C.

Disposal:

• P501: Dispose of contents/container to an approved waste disposal plant.

Other Hazards

• The mixture contains no vPvB substances (vPvB = very persistent, very bioaccumulative).
• The mixture contains no PBT substances (PBT = persistent, bioaccumulative, toxic).
• The mixture contains no substances with endocrine-disrupting properties.

WD-40 Company Limited Zweigniederlassung Deutschland, Siemensstrasse 21, 61352 Bad Homburg, GERMANY, +49 6172 677 450, [email protected], www.wd40.de